Vape & Make
Items 1 - 50 of 51
- Developed in cooperation with our partner Feed3D Mods .
- Height-adjustable attachment to the 510 .
- Protection against twisting when screwing on / unscrewing the vaporizer .
- Flattened stop plate for maximum current flow .
- Three variants, with a total of 6 different distances from connector / to plate.
- Made from neodymium-iron-boron (Nd2Fe14B)
- Surface nickel-plated (Ni-Cu-Ni)
- Various heights
- 8 pieces per pack.
Graduated prices for all magnets
Graduated prices for all magnets
Graduated prices for all magnets
- 8 pieces
- .
- 62 x 12 mm each
- Printed in very high quality using SLS (Selective Laser Sintering).
- Precisely fitting production, nothing wobbles here.
- To install the display , first connect the display to the board. Then insert the display into the holder and press it carefully and to its full width (use both hands).
- Lock Ring designed for the ReseT ModS 510 Squonk Connector.
- Perfect fit for the ReseT nut.
- Sizes specially adapted for modding
- From 2mm cable (AWG22) up to 510, push button, mosfet
- In the colors red and black
- Shrink ratio 2:1
- Suitable for the DNA250C chip according to Evolv specifications
- Silicone cable highly flexible and fine-stranded according to DIN VDE 0295 cl.6
- 2 x AWG 12, 15cm each, red/black
- 2 x AWG 18, 15cm each, red/black
- 2 x AWG 24, 15cm each, red/black
- Suitable for the DNA60 chip according to Evolv specifications
- Silicone cable highly flexible and fine-stranded according to DIN VDE 0295 cl.6
- 2 x AWG 14, 15cm each, red/black
- 2 x AWG 18, 15cm each, red/black
- 2 x AWG 24, 15cm each, red/black
- Suitable for the DNA60C chip according to Evolv specifications
- Silicone cable highly flexible and fine-stranded according to DIN VDE 0295 cl.6
- 2 x AWG 14, 15cm each, red/black
- 2 x AWG 18, 15cm each, red/black
- 2 x AWG 24, 15cm each, red/black
- Suitable for the DNA60 chip according to Evolv specifications
- Silicone cable highly flexible and fine-stranded according to DIN VDE 0295 cl.6
- 2 x AWG 14, 15cm each, red/black
- 2 x AWG 16, 15cm each, red/black
- 2 x AWG 24, 15cm each, red/black
- Suitable for the DNA60 chip according to Evolv specifications
- Silicone cable highly flexible and fine-stranded according to DIN VDE 0295 cl.6
- 2 x AWG 14, 15cm each, red/black
- 2 x AWG 16, 15cm each, red/black
- 2 x AWG 24, 15cm each, red/black
- Five different colors .
- Fine adjustment via mini potentiometer on the back .
- Reverse polarity protection .
- 2.4 to 30 volts.
- Four different colors .
- Fine adjustment via mini potentiometer on the back .
- Reverse polarity protection .
- 0 to 100 volts .
- Resolution below 10V 0.01, above 10 volts 0.1.
- Suitable for the usual voltmeters used in mod construction
- Made of 6061 aluminum, anodized
- External dimensions: 30 x 18 x 4 mm
- Internal dimensions: 25 x 13 x 3 mm Voltmeter shown is not included in the scope of delivery
- Lock ring for the nut of the Moddog Nano connector .
- Perfect fit for the ModDog 15mm socket.
- Special tool for tightening the Nano connector nut. .
- Not absolutely necessary - but makes assembly much easier .
- Use only for assembly, not to adjust the pin height later!
- Made from stainless steel .
- Black color applied with VaKuum process .
- Diameter 12mm, stop 1mm .
- Total height 4.1 mm .
- Concave rounding on the actuation side.
- Suitable for the usual "93PR" pots from TT Electronics .
- Made of 6061 aluminum, anodized .
- Radius inside: 13.07 mm, outside: 18.09 mm, height 4.03 mm .
- Potentiometer shown is not included in the scope of delivery.
Important note: The battery holder offered here is not a product of the company "Keystone". The holder comes from "Blossom Electronics", the contacts from Keystone. We have combined both into our own product and sell it under the "Vape & Make" brand.
- Battery holder for 2 x 18650 lithium ion cells
- Made from nylon by injection molding
- Contacts 4 x Keystone 1107-1 plug-in contact with solder lug
- The rescue for every cell with a damaged casing
- Complete protection for 2 x 18650 cells
- Double silicone cover with fixing eyelet
- 10 x heat shrink tubing in Coil Master design
- Ideal for on the go but also a safe solution at home
- Four push buttons for Evolv DNA boards. One large power button (Ø 8mm) and three small control buttons (Ø 4mm)
- Length optimized for boxes with a wall thickness of 2mm
- Three different colours/materials: silver (stainless steel), black (anodized aluminium), golden yellow (brass)
Top rated
Gap dimensions (for acrylic sheet)
- Gap width: 4.7mm (± 0.1mm). Suitable for 3 to 4.5mm acrylic sheet
- Gap length: 71.5mm
- Gap depth: 16.3mm
LED version
- 16 colors (with remote control), 7 colors (with Smart Touch)
- Dimming, flashing, color change, color transition
Would you like other quantities or different combinations? Please contact us.
Best sellers
Gap dimensions (for acrylic sheet)
- Gap width: 5.2mm (± 0.1mm). Suitable for up to 5mm sheet
- Gap length: 94.5mm (rounded corners)
- Gap depth 3 colors: 19.1mm, 7 colors: 18.4mm
LED version
-
3 colors: Warm white, neutral white, mixed
- Dimmer
-
7 colors: red, green, blue, yellow, cyan, pink, white
- Dimmer, color change, color transition (fast/slow)
Would you like other quantities or different combinations? Please contact us.
- The best of both worlds, the V&M Okto silicone bottle
- As much content as a square bottle and a pleasant squeezing sensation like a round bottle
- Extra flat Ultem cap for more content and with a width of only 14.5 mm for more space in the mod
- Bottle with 2.4 ml capacity (18350), diameter 17.5 mm, height 21 mm
Gap dimensions (for acrylic sheet)
- Gap width: 4.7mm (± 0.1mm). Suitable for 3 to 4.5mm acrylic sheet
- Gap length: 71.5mm
- Gap depth: 16.3mm
LED version
- 16 colors (with remote control), 7 colors (with Smart Touch)
Would you like other quantities or different combinations? Please contact us.
- Very space-saving with a total length of only 12.6 mm .
- Pleasant pressure point and not too loud "click" .
- Stable colors due to anodization .
- Made from aluminum/stainless steel .
- RoHs, REACH, IP67, IK08, CQC certification .
Best sellers
Gap dimensions (for acrylic sheet)
- Gap width: 5.2mm (± 0.1mm). Suitable for up to 5mm acrylic sheet
- Gap length: 119mm (rounded corners)
- Gap depth 1 color: 22.3mm, 3 colors: 21.5mm, 7 colors: 19.5mm
LED version
- 1 color: warm white
-
3 colors: Warm white, neutral white, mixed
- Dimmer
-
7 colors: red, green, blue, yellow, cyan, pink, white
- Dimmer, color change, color transition (fast/slow)
Would you like other quantities or different combinations? Please contact us.
- Developed in cooperation with our partner Feed3D Mods .
- Left-hand thread to prevent accidental loosening .
- Adjustable nut (sheet metal stop point) with flattened contact point .
- Complete plus-pole contacts gold-plated.
Out of stock
Gap dimensions (for acrylic sheet)
- Gap width: 4.1mm (± 0.1mm). Suitable for 3 to 4mm acrylic sheet
- Gap length: 66.7mm (rounded corners)
- Gap depth: 17.5mm
LED version
- 7 colors: red, green, blue, yellow, cyan, pink, white
Would you like other quantities or different combinations? Please contact us.
- Super soft silicone with a dark tint .
- Height-adjustable thanks to two accordion ribs. The height is between 45 and 50 mm .
- Capacity 6 to 8ml (without tube). The diameter is 17mm .
- Closure 13 mm, extra tight .
- Tested for food safety by the SGS Institut Fresenius .
Gap dimensions (for acrylic sheet)
- Gap width: 5.1mm (± 0.1mm). Suitable for up to 5mm acrylic sheet
- Gap length: Version 180mm: 150mm; 200mm: 170mm; 240mm: 210mm; 300mm: 270mm (rounded corners)
- Gap depth: 2.1mm
LED version
- Warm white (2700 Kelvin).
- Possible alternatives on request: warm white/neutral white/mixed or RGB.
Basic version
- Length 180mm, 200mm, 240mm or 300mm.
Other quantities or different combinations required? Please contact us.
Best sellers
- Very space-saving with a total length of only 15.8 mm .
- Pleasant and not too loud "click" .
- Stable colors due to anodization .
- Made from aluminum/stainless steel .
- RoHs, IP67, IK08 certification .
Out of stock
- Printed using laser printing (SLS)
- Precisely fitting production, nothing wobbles here.
- To install, insert the chip / display into the holder. Then press carefully on the other side over the full width (use both hands).
Included components
- Combined chip / battery holder: Vape & Make
- Insulation box bottom: Vape & Make
- Battery contacts: Keystone
- Soldering lug: Rosenberger
- Modding box with sliding lock.
- CNC machined from 6061-T6 aluminum.
- Sandblasted and anodized.
- Right-angled and the magnets are not continuous.
- Outside size: 102 x 51 x 28mm, inside size: 99.3 x 48.3 x 23mm.
- Modding box with sliding lock
- CNC machined from 6061-T6 aluminum
- Sandblasted and anodized
- Special lid shape results in maximum usable interior space
- External size: 112 x 60.5 x 32mm, internal size: 108 x 57 x 28mm
- Two copper sheets suitable for the TLF#
- With some adaptation also suitable for many other squonkers
- Hole for 510 pre-drilled, elevations for battery support
- Rounded corners, de-radiused.
- Complete build kit for the TLF# Squonker
- Developed in collaboration between TLF# and Vape & Make
- A Coil Master microfiber cloth for cleaning is included FREE of charge
- Kit contains all components except box, door, button and lock ring
Included components
- Copper plates: Made in Spain by MART&GON
- Liquid bottle: Vape & Make, ModMaker or Coil Master, depending on your choice
- 510 Botton Feeder Connector: Vape & Make or ReseT Mods depending on selection
- Magnets: Vape & Make
- Battery strap: Vape & Make
- Microfiber cloth: Coil Master, ideal for cleaning the squonker (but also suitable for glasses :-)
Out of stock
- All necessary parts available.
- Box with sliding closure.
- Engraving (as an option) possible.
Technical design.
- Etileno PWM control.
- 2 x 21700 battery.
- 30mm top cap.
Included components.
- Box: Vape & Make 1590B with sliding cap.
- 510: ModMaker / Steathvape.
- Controller: Etileno PWM.
- Power button: Vape & Make.
- Battery holder: MosMax 2 x 21700.
- Cable: Silicone highly flexible, 2 x 30cm 14 AWG and 24 AWG each.
- +/- Warning stickers: Vape & Make, 4 pieces.
Out of stock
- Small, handy box (86 x 44 x 28mm) with 21700 battery.
- Combined chip / battery holder.
- All soldering work possible outside the box.
- Plenty of tolerance for all components.
Technical structure.
- EVOLV DNA 75 Color Board.
- 21700 battery.
- 22mm top cap.
- Chip/battery holder glued in box (not screwed).
Documentation and downloads.
- Information about the box: Assembly instructions.pdf.
- Information about the DNA 75C: DNA 75 Color.pdf.
- EVOLV control software: EScribe.
Included components.
- Box: Analog Box Mods V1 incl. magnets.
- Button: Analog Box Mods.
- 510: ModMaker 510 Micro, 22mm top cap.
- Controller: Evolv DNA 75C.
- Combined chip/battery holder: Vape & Make.
- Insulation box bottom: Vape & Make.
- Cable: Muldental silicone high flexible, 14 and 24 AWG.
- Battery contacts / solder lug: Keystone / Rosenberger.
- All required components.
- EVOLV DNA 250 color Board with reverse polarity protection.
- EVOLV DNA 75 color Board with reverse polarity protection.
- Designed for 2 batteries in series connection (2S)
- External dimensions 89 x 61 x 28, internal dimensions 84 x 57 x 24 mm
Technical structure
- 2 x 18650 batteries, connected in series.
- EVOLV DNA 250 color Board with reverse polarity protection.
- EVOLV DNA 75 color Board with reverse polarity protection.
- 22mm top cap.
- Chip holder glued in box (not screwed).
Documentation and downloads
Included components
- Box: Analog Box Mods V2 incl. magnets.
- 510: Fat Daddy Vapes / ModMaker / Steathvape.
- Controller: Eolv DNA 250C.
- Controller: Eolv DNA 75C.
- Chip holder: Vape & Make 3D laser sinter print.
- Button: Analog Box Mods.
- Battery holder: Vape & Make 2 x 18650, ground on the right side.
- Battery holder contacts: Keystone 4 x 1107-1
- Cable: Silicone highly flexible, 2 x 15cm each 14 AWG, 16AWG and 24 AWG.
- +/- Warning stickers: Fat Daddy Vapes, 4 pieces.
- Original Analog Box Mods, Canada
- "Velvety soft" feel thanks to powder-coated surface.
- Individual motif engraved using CO² laser
- Each color-motif combination is unique
Top rated
- All required components.
- EVOLV Color Board with reverse polarity protection.
- Designed for 2 batteries in series connection (2S).
- External dimensions 96 x 65 x 32, internal dimensions 91 x 61 x 28 mm.
Technical design.
- 2 x 20700/21700 batteries, connected in series.
- EVOLV Color Board with reverse polarity protection.
- 22mm top cap.
- Chip holder glued in box (not screwed).
Documentation and downloads.
Included components.
- Box: Analog Box Mods V2 incl. magnets.
- 510: Fat Daddy Vapes / ModMaker / Steathvape.
- Controller: Eolv DNA 250C / DNA 75C.
- Chip holder: Vape & Make 3D print.
- Button: Analog Box Mods.
- Battery holder: MosMax 2 x 21700.
- Cable: Silicone highly flexible, 2 x 15cm 14, 18 and 24 AWG each.
- +/- Warning stickers: Fat Daddy Vapes, 4 pieces.
Items 1 - 50 of 51