Evolv DNA 75C (Color) Board incl. V&M Board Holder

Evolv DNA 75C (Color) Board incl. V&M Board Holder

SKU: EV-DNA-75C-mit
Manufacturers: Evolv

Data sheet and instructions: DNA 75 Color.pdf .
Control software: EScribe .
Link to the manufacturer: Evolv .

Holder printed from Green TEC filament, heat resistant up to 180°C. .
Accurate manufacturing, nothing wobbles here. .
To install, insert the chip / display into the holder. Then press carefully and on full width (use both hands).

Variant: incl. V&M board holder54,31 €

without board holder52,74 €

54,31 €

incl. 19% VAT , plus

From	Unit price
1	54,31 €*

Available immediately
Delivery time: 1 - 2 Workdays (DE - int. shipments may differ)

This item has variations. Please select the requested variation.

Configure

Matching accessories

optional

Order now - in a bundle with discount

Fat Daddy 510 Connector V. 3LP, spring-loaded, for battery carrier/tube, 15-30mm top cap +8,07 €

The original from the USA .
Insulation made of zirconia ceramic. This material can withstand temperatures of over 1000°C and offers excellent insulation .
High-performance connector with a permanent load capacity of up to 500 watts .
Suitable for all chipsets on the market .
With 11.25mm also suitable for small mods.

Item details

Quantity: 1

Source 510 Connector V2, spring-loaded, f. battery carrier/tubes, 22-40mm top cap +9,80 €

The popular Source Connector from Steath-Vape here in version 2. .
Available with 22 mm, 24 mm, 25 mm and 30 mm top cap. .
22mm Top Cap also in black .
Flat Top - without cutouts .

Item details

Quantity: 1

V&M /- Stickers for battery compartment, 8 pieces +3,37 € +2,94 €

8 pieces
.
each 62 x 12 mm

Item details

Quantity: 1

Cable set for DNA60, red/black, AWG 14, 18, 24, 15cm each +4,09 € +3,67 €

Suitable for DNA60 chip according to Evolv specifications
Silicone cable highly flexible and fine-stranded according to DIN VDE 0295 Kl.6
2 x AWG 14, each 15cm, red/black
2 x AWG 18, each 15cm, red/black
2 x AWG 24, each 15cm, red/black

Item details

Quantity: 1

Cable set for DNA60C, red/black, AWG 14, 18, 24, 15cm each +4,09 € +3,67 €

Suitable for the DNA60C chip according to Evolv specifications
Silicone cable highly flexible and fine-stranded according to DIN VDE 0295 cl.6
2 x AWG 14, 15cm each, red/black
2 x AWG 18, 15cm each, red/black
2 x AWG 24, 15cm each, red/black

Item details

Quantity: 1

V&M Voltmeter 0.28", 3 cables red +4,5 € +4,07 €

Four different colors .
Fine adjustment by mini potentiometer on the back side . .
Reverse polarity protection .
0 to 100 volts .
Resolution below 10V 0.01, above 10 volts 0.1.

Item details

Quantity: 1

V&M Voltmeter 0.28", 3 cables green +4,5 € +4,07 €

Four different colors .
Fine adjustment by mini potentiometer on the back side . .
Reverse polarity protection .
0 to 100 volts .
Resolution below 10V 0.01, above 10 volts 0.1.

Item details

Quantity: 1

V&M Voltmeter 0.28", 3 cables yellow +4,5 € +4,07 €

Four different colors .
Fine adjustment by mini potentiometer on the back side . .
Reverse polarity protection .
0 to 100 volts .
Resolution below 10V 0.01, above 10 volts 0.1.

Item details

Quantity: 1

Cable set for DNA100C, red/black, AWG 14, 18, 24, 15cm each +4,16 € +3,73 €

Suitable for DNA60 chip according to Evolv specifications
Silicone cable highly flexible and fine-stranded according to DIN VDE 0295 Kl.6
2 x AWG 14, each 15cm, red/black
2 x AWG 16, each 15cm, red/black
2 x AWG 24, each 15cm, red/black

Item details

Quantity: 1

Cable set for DNA75C, red/black, AWG 14, 18, 24, 15cm each +4,16 € +3,73 €

Suitable for DNA60 chip according to Evolv specifications
Silicone cable highly flexible and fine-stranded according to DIN VDE 0295 Kl.6
2 x AWG 14, each 15cm, red/black
2 x AWG 16, each 15cm, red/black
2 x AWG 24, each 15cm, red/black

Item details

Quantity: 1

V&M heat shrink tubing assortment, black/red, 127 parts, 2/2.5/3.5/5/7/10/13mm +4,11 € +3,56 €

Sizes specially adapted for modding
From 2mm cable (AWG22) up to 510s, pushbuttons, mosfet
In the colors red and black
Shrink ratio 2:1

Item details

Quantity: 1

Cable set for DNA250C, red/black, AWG 12, 18, 24, 15cm each +4,33 € +3,91 €

Suitable for DNA250C chip according to Evolv specifications
Silicone cable highly flexible and fine-stranded according to DIN VDE 0295 Kl.6
2 x AWG 12, each 15cm, red/black
2 x AWG 18, each 15cm, red/black
2 x AWG 24, each 15cm, red/black

Item details

Quantity: 1

Jmate magnetic USB charging cable 90cm, compatible with JUUL e-cigarette +4,72 € +4,29 €

It is no longer easier to charge your e-cigarette .
The strong magnets hold the device securely .
Charging in 15 minutes.
90 cm long cable for greater mobility easy use of sockets.

Item details

Quantity: 1

V&M Aluminum Bezel for Voltmeter 0,28" Black +4,75 € +4,32 €

Fits the usual voltmeters in mod building.
.
made of 6061 aluminum, anodized
.
outside dimensions: 30 x 18 x 4 mm
.
inside dimensions: 25 x 13 x 3 mm

Item details

Quantity: 1

V&M aluminum bezel for voltmeter 0.28" silver +4,75 € +4,32 €

Fits the usual voltmeters in mod building.
.
made of 6061 aluminum, anodized
.
outside dimensions: 30 x 18 x 4 mm
.
inside dimensions: 25 x 13 x 3 mm

Item details

Quantity: 1

Fat Daddy 510 Connection Tool +4,43 € +4,00 €

Simple but ingenious tool
Fixes the 510 connector for easy installation

Item details

Quantity: 1

V&M aluminum bezel for voltmeter 0.28" red +4,75 € +4,32 €

Fits the usual voltmeters in mod building.
.
made of 6061 aluminum, anodized
.
outside dimensions: 30 x 18 x 4 mm
.
inside dimensions: 25 x 13 x 3 mm

Item details

Quantity: 1

V&M Aluminum Bezel for Voltmeter 0,28" Blue +4,75 € +4,32 €

Fits the usual voltmeters in mod building.
.
made of 6061 aluminum, anodized
.
outside dimensions: 30 x 18 x 4 mm
.
inside dimensions: 25 x 13 x 3 mm

Item details

Quantity: 1

V&M special tool for ModDog 510 Nano nut +4,8 € +4,37 €

Special tool for tightening the Nano connector nut. .
Not absolutely necessary - but makes the assembly much easier .
Use only for assembly, not to adjust the pin height later!

Item details

Quantity: 1

V&M Voltmeter 0.28", 3 cables Blue +4,97 € +4,54 €

Four different colors .
Fine adjustment by mini potentiometer on the back side . .
Reverse polarity protection .
0 to 100 volts .
Resolution below 10V 0.01, above 10 volts 0.1.

Item details

Quantity: 1

V&M aluminum bezel for potentiometer red +5,26 € +4,84 €

Fits the usual "93PR" pots from BI Technologies / TT Electronics.
.
made of 6061 aluminum, anodized
.
inner radius 13.07 mm, outer radius 18.09 mm, height 4.03 mm
is

Item details

Quantity: 1

V&M aluminum bezel for potentiometer blue +5,26 € +4,84 €

Fits the usual "93PR" pots from BI Technologies / TT Electronics.
.
made of 6061 aluminum, anodized
.
inner radius 13.07 mm, outer radius 18.09 mm, height 4.03 mm
is

Item details

Quantity: 1

V&M Aluminum Bezel for Potentiometer Black +5,26 € +4,84 €

Fits the usual "93PR" pots from BI Technologies / TT Electronics.
.
made of 6061 aluminum, anodized
.
inner radius 13.07 mm, outer radius 18.09 mm, height 4.03 mm
is

Item details

Quantity: 1

Power Mosfet IRLB3034PBF, N-channel, incl. resistor and 15A fuse +5,16 € +4,73 €

The best MOSFET for moderators and makers
Allows the use of any fire button. Also recommended as a safety device for high-amp fire switches.
The required 15K Ohm resistor is also included.
Alternatively with one or two MHP-TA15-9-72 fuses.
This trips at 75°C and opens again when it gets colder

Item details

Quantity: 1

Goobay solder lead-free, with flux, 3.5% silver, ø 1.0 mm, 12.5 g +5,02 € +4,47 €

Composition: 3.5 % silver, 0.7 % copper, 93.8 % tin; flux content: 2 %; melting point 217° C
significantly improved electrical conductivity due to silver content (3.5 %)
no cleaning of solder joints after soldering necessary
"No-clean solution" with continuous flux cores
halogen-free and low smoke emission.

Item details

Quantity: 1

Coil Master ceramic tweezers Angled +6,33 € +5,78 €

Impressive values. Available in white, black or white angled. .
Made of 302 stainless steel and Zirconia ceramic. .
Temperature resistance up to 1600°C and hardness greater than HRC40° . .
Matte finish with Coil Master lettering . .
Certificate of authenticity for online verification on the back of the packaging.

Item details

Quantity: 1

Reset Mods special tool (wrench) for the ReseT ModS connector +6,84 € +6,41 €

Special tool for Reset Mods squonker connectors .
Not a must, but makes installation much easier.

Item details

Quantity: 1

V&M button for Evolv DNA boards, color: silver (stainless steel) +6,65 € +6,22 €

Four push buttons for Evolv DNA boards. One large power button (Ø 8mm) and three small control buttons (Ø 4mm)
Length optimized for boxes with a wall thickness of 2mm
Three different colours/materials: silver (stainless steel), black (anodized aluminium), golden yellow (brass)

Item details

Quantity: 1

2 x Delo Duopox rapid 01, 2-component universal high-performance epoxy adhesive, 3g +6,42 € +5,99 €

Universal 2k epoxy resin adhesive, room temperature curing
Preparation: Surfaces to be bonded should be dry, free of dust, grease and other contaminants
Processing: Cut open the sachet, empty the contents completely and mix both components intensively for approx. 30 s
Working time 4 minutes. Curing Manual strength 8 minutes, functional strength 2 hours, final strength 24 hours.
✔ Conveniently packaged in packs of 2.

Item details

Quantity: 1

V&M button for Evolv DNA boards, black (anodized aluminium) - Item currently out of stock +6,93 € +6,50 €

Four push buttons for Evolv DNA boards. One large power button (Ø 8mm) and three small control buttons (Ø 4mm)
Length optimized for boxes with a wall thickness of 2mm
Three different colours/materials: silver (stainless steel), black (anodized aluminium), golden yellow (brass)

Item details

Quantity: 1

V&M button for Evolv DNA boards, golden yellow (brass) +6,93 € +6,50 €

Four push buttons for Evolv DNA boards. One large power button (Ø 8mm) and three small control buttons (Ø 4mm)
Length optimized for boxes with a wall thickness of 2mm
Three different colours/materials: silver (stainless steel), black (anodized aluminium), golden yellow (brass)

Item details

Quantity: 1

Source 510 Konnector V3, spring-loaded, for battery carrier/tubes, 22mm, silver +10,31 € +9,76 €

The popular Source Connector from Steath-Vape in version 3.
Available with 22 and 30 mm Top Cap.
Each in the colors silver (stainless steel) and black.
As well as with the soldering options standard and vFlat.
Now again with the usual M10 thread.

Item details

Quantity: 1

Fat Daddy drill/tap combo +12,47 € +11,92 €

Special tool from Fat Daddy Vapes
On the one hand a drill for the 510 hole
On the other hand a tap for the 510 thread
So the 510 sits absolutely tight
Also for boxes with already existing 510 hole

Item details

Quantity: 1

Up/Down ( /-) circuit board for Billet Box / Boro +15,98 € +15,56 €

Replacement circuit for regulating the power of the box with the + and - buttons.
Includes cable for soldering to the controller.
Works on the original billet box and clones.

Item details

Quantity: 1

V&M copper plates for 18650 squonker +22,08 € +21,53 €

Two copper sheets suitable for the TLF#.
With some adjustment but also suitable for many other squonkers
Hole for 510s pre-drilled, elevations for battery support
Corners rounded, degraded.

Item details

Quantity: 1

Your configuration

incl. 19% VAT , plus shipping costs

Description

The DNA 75 Color is a power regulated digital switch-mode DC-DC converter for personal vaporizers.

It features Evolv's patented Wattage Control, Patent Pending Temperature Protection, Preheat, Onboard Buttons, Synchronous Rectification for maximum battery life and minimal heat generation, and a 160 x 80 pixel Color TFT Screen.

The DNA 75 Color runs from a single cell lithium polymer battery.

Evolv's EScribe 2.0 and Theme Designer software can be used to make the DNA 75 Color look and act exactly like you want.

Designed for ease of use while allowing complete customization, the DNA 75 Color is vaping down to a science.

Dimensions ( Length × Width × Height ):	6,60 × 1,80 × 0,80 cm
Included items:	DNA75C board, 0.9" TFT color display
Plug type:	USB, 1 amp