Vaoe & Make Copper Sheets for TLF#

Item number: VM-TLF#-Copper


23,26 €

including 19% VAT. , plus shipping

From Price per unit
2 20,80 €
3 19,88 €
5 19,16 €
Available now!

Shipping time: 1 - 2 workdays



It took a long time, but it has become even better. The Build Kit for the TLF# Squonker.

Developed in collaboration with TLF# and Vape & Make and manufactured by specialists in Spain, UK, USA and Germany.

Available now on eBay as a complete kit but also in individual components.

You can find the housing / door / button / lock ring on the usual place at Shapeways with the search term "TLF#" (links not allowed on eBay).

Everything else you need for this popular Sqounker comes along with the kit. Along with the copper sheets you will get the 510 connector, the bottle, two magnets, a satin ribbon for easier removal of the battery and a little microfiber cloth.

When ordering on Shapeways and ebay, assemble according to the enclosed instructions, screw on the BF/RDA, fill in the liquid and you're good to go with your TLF#.


Copper sheets
  • Made in Spain by MART&GON
  • Perfectly cut and curved with rounded and straightened edges on the outside as well as on the hole for the 510er
  • Dimples on the battery contact surfaces

  • Liquid bottle
  • Made by Mod Maker in England
  • It comes with a soft thin wall bottle, a stainless steel knurled cap, a silicone tubing and a silicone washer. The bottle holds 8.5ml of juice. The washer probably won't be need but it is included in case your lid doesn't seal 100% with the bottle.
  • To insert the hose simply cut the end at a 45 degree angle and twist through the hole. It is a reasonably tight fit and provides a very good seal.

  • 510 Bottom Feeder Connector
  • Made by Mod Maker in England
  • Glass filled peek insulator. This material can take some serious heat. Wave spring. A stiffer spring for a better connection. Oring / gasket. Embedded into the positive pin to reduce leakage. Negative solder tab. For non mechanical squonkers.
  • The threaded section is m12 (12mm x 1mm) thread. The top plate is 16mm diameter and 0.5mm thick. When you add a washer, the top plate will be 1mm thick.

  • Magnets
  • Made of neodymium by Mod Maker in England

  • Battery strap
  • For easier removal of the battery

  • Microfiber cloth
  • From Coil Master from the US. Ideal for cleaning the Squonker (but also suitable for spectacles)

  • Build Kit complete:
  • Two copper sheets for the connection of the battery and the 510 connector via the power button and for the connection back from 510 connector to the battery.
  • Mod Maker 510 Bottom Feeder connector and a washer with 22mm diameter.
  • Mod Maker Squonker Bottle Kit, capacity 8.5 ml.
  • Two neodymium magnets 5 x 1 mm (width/height).
  • Satin battery strap 6.5 cm.
  • Coil Master microfiber cloth 15 x 15 cm.

  • Copper sheets only:
  • Two copper sheets for the connection of the battery and the 510 connector via the power button and for the connection back from 510 connector to the battery.

  • 510 connector only:
  • Mod Maker 510 Bottom Feeder connector and a washer with 22mm diameter.

  • Squonker bottle only:
  • Mod Maker Squonker Bottle Kit, capacity 8.5 ml.

  • Magnets only:
  • Ten neodymium magnets 5 x 1 mm (width/height).
  • Not sure if you already checked out the ATTENTION notes on Shapeways.com but there are some small things to pay attention for:

  • scrap out the rest of powder especially below the bottom plate of the bottle and the slot of the battery strap
  • evtl. widen the holes of the button and 510 to get a proper fit
  • to get the battery strap sit tight burn down one end with a lighter until it stuck in the hole
  • don't bend the positive battery to full 90 degrees to get a proper tension on the button
  • to fix the button use a thin piece of adhesive tape

  • Depending on what 510 (MM510) you are using it is helpful to follow the steps below for assembling

    1. install the positive battery plate
    2. install the negative battery plate without tighten the 510
    3. install a battery to get the final plate position
    4. install the button by lifting the positive battery plate
    5. !!! REMOVE BATTERY
    6. if you want to use 8,5ml bottle you'll have to shorten the 510 Pin
    7. tighten the 510 and the negative battery plate and you're good to go (try to fix the nut and then tighten the 510 with an old Atty instead of trying to tighten the nut)

    Please login first to add a tag.